STOCKLIST OUTLET CONTACT ENGLISH NEDERLANDS FRANCAIS ESPAÑOL
MANUALS SIZES MADE TO MEASURE FABRICS TENT PARTS

WASHING INSTRUCTIONS


Use a jetwasher. Never go closer then 20cm!

Use a soft brown/black soap with a soft sponge to remove stains

Never use aceton / thinner or any kind of solvent

PUT THE CENTER POLES

Warning: Never put a center pole without a polecap!






























Start with the side poles of the tent. Keep the center poles always  for last.

PUT THE POLE CAP ON THE CENTER POLES


USE OF ALUMINIUM  POLES 40MM DIAMETER:

If you use alumium poles of 40mm diameter or

60mm diameter, you can easily slide them on the poles.


USE OF WOODEN POLES: If you use wooden poles, you can follow these steps:

1. make a hole in the wood, screw the wood adaptor onto the wooden pole

2. slide the pole cap over it.

SETUP: STEP 5


PUT UP THE SIDE POLES

Put up the 4 corners. Adjust the straps so they are still quite loose.

USE OF ALUMINIUM  POLES 40MM DIAMETER


Slide the grip into the aluminium pole of 40 diameter














1.

make a hole in the top of your pole of 13mm diameter and 60mm deep

2.

unscrew the grip


3.

put back the extra long M8 nut


4.

slide the screw into the hole of the wooden pole



If you wish to use wooden poles on the corners follow these instructions (skip this step if you use aluminium standard poles):

1.

make a hole in the top of your pole of 13mm diameter and 60mm deep

2.

unscrew the grip


3.

put back the extra long M8 nut


4.

slide the screw into the hole of the wooden pole



SETUP: STEP 4


USE OF WOODEN POLES (skip this step if you use aluminium standard poles)

If you wish to use wooden poles on the sides follow these instructions:

ATTACH THE STRAPS BETWEEN THE PEGS AND THE FIXINGS

Make the tension on the straps very loose.

SETUP: STEP 3


PUT THE PEGS

The Bonga Stretchtent is standard delivered with pegs for lawn and clay.

If you have another surface, please use the suitable pegs!

The distance (D) of the pegs from the tent is equal to the height  (H) of the pole you will use (H=D).

The pegs should be placed under an angle of 45° for optimal grip and force resistance.

ATTACH THE STRAPS TO THE CLAMPS

SETUP: STEP 2


ATTACH THE SIDE CLAMPS


Take the plan ‘REINFORCED ZONES’ delivered with the tent to guide you further

Only put the side clamps on the reinforced zones! You can see and feel them when you go over  the canvas

Always make sure the grip is well tightened! Check before you put up the tent!

RIGHT SIDE UP

The tent is always delivered with the corner fixings attached.

When you unfold the tent, the grips of the corner fixings should face the ground.

Warning: always make sure the grip is well tightened! Check before you put up the tent!




SETUP: STEP 1


PROTECT YOUR TENT

Unfold a plastic groundsheet to prevent stains

Unfold the tent on the plastic groundsheet

Download the manual of your tent:

SETUP INSTRUCTIONS


Don’t put too much tension on the straps! Just a little, so the canvas is off the ground.

Put up the 2 other sides

Put up 2 oposite sides. Always choose the sides in the direction of the wind.

DOWNLOAD MANUAL 6,5mx5m

DOWNLOAD MANUAL 6,5mx6,5m

DOWNLOAD MANUAL 10mx6,5m

Lanes 10m

DOWNLOAD MANUAL 10mx8,5m

Lanes 8,5m

DOWNLOAD MANUAL 10mx10m

DOWNLOAD MANUAL 10mx12m

DOWNLOAD MANUAL 10mx15m

DOWNLOAD MANUAL 10mx20m

DOWNLOAD MANUAL 15mx20m

GENERAL INSTRUCTIONS


ALWAYS PUT A CLAMP AT LEAST EVERY 2 METER ON A REINFORCED ZONE

NEVER USE STRAPS WITH RATCHETS, USE THE STRAPS DELIVERED WITH THE TENT

DOWNLOAD MANUAL 10mx6,5m

Lanes 6,5m

DOWNLOAD MANUAL 10mx8,5m

Lanes 10m